/
Vertical Bun Toaster Operation

Vertical Bun Toaster Operation

Owned by Yasmin Rooney (Deactivated)
Last updated: Dec 20, 2021
5 min read

Operating Instructions

1. Set the bun / bread thickness.

  1. Turn the power on.

  2. Turn the temperature control to 10 and allow the toaster to warm up for 30mins.

  3. Drop buns into toaster cut sides of crown and heel facing each other. Product will drop on the landing tray at the bottom.

  4. Turn off power when finished and clean as per daily cleaning procedure.

 

Left

Right

 

Left

Right

Settings

6

3

Products

Crowns/Thick Toast/Ciabatta

Heels/Thin Toast

 

 

 

Daily Cleaning Vertical Bun Toaster

Tools Required:

  • Heat-Resistant Gloves

  • Clean Towels

  • Multipurpose Detergent Solution

  • Sanitizer Solution

 

  1. Turn the power off, unplug the power cord, and allow the unit to cool for 30 minutes.

  2. Put on heat resistant gloves. Remove the Bun Feeder, Heat Shield, and Bun Chute.

3. Wipe the Bun Feeder, Heat Shield, and Bun Chute with a damp sanitized cloth and allow them to air dry.

4. Remove the Release Sheet and place it on a clean, flat dry surface.

 

Release Sheet

 

5. Wipe the silver side with a clean cloth dampened with All Purpose Cleaner immediately followed by a second cloth dampened with sanitizer. Allow it to air dry before continuing.

6. Once the silver side of the Release Sheet is dry, repeat Step 5 on the black side. If properly cleaned, the Release Sheet surface should be smooth to the touch when dry.

7. Install a new or clean Release Sheet, using the reverse side, by draping it over both sides of the Platen with the crease centered on the Platen. NOTE: Rotate from side to side daily or weekly to prolong the life of the Release Sheet.

8. Install the Bun Chute so the hooks are installed over the lower rear yellow Support Rod.

9. Install the Heat Shield with the Release Sheet retainer clips securely over the Release Sheet and Platen.

10. Wipe down the outside of the toaster with a clean, damp, sanitized cloth.

 

Conveyor Belt Clean (Weekly)

 

After step 6 in daily clean

  1. Open the front Conveyor Cover and firmly wipe the Belt Wrap from left to right and top to bottom with a clean cloth dampened with All Purpose Cleaner immediately followed by a second cloth dampened with sanitizer solution.

CAUTION: Turn the power off, disconnect the power cord, and allow the unit to cool down 30 minutes before performing any service or maintenance.

 

CAUTION: To prevent damage to the unit, do not use abrasive cleaners on the Release Sheet or belt wrap.

 

 

2. Close the front Conveyor Cover, open the rear Conveyor Cover, and clean the Belt Wrap as described in Step 7.

3. Close the rear Conveyor Cover and reinstall the Heat Shield. Then plug in the power cord, turn the unit on, count 10 seconds, then turn the unit off and unplug the unit. This will allow the uncleaned sections to be exposed.

4. Open the rear Conveyor Cover again, clean the newly exposed section of the Belt Wrap in the same manner as before. Close the Conveyor Cover.

5. Open the front Conveyor Cover again and clean the newly exposed section of the Belt Wrap (if used) or Conveyor Belt Chain in the same manner as before.

6. Close the front Conveyor Cover and wipe down the outside of the toaster with a clean, damp, sanitized towel.

Complete step 7, 8 & 9 of daily cleaning.

 

Replacing Release Sheet and Belt Cover

 

Release Sheet

Replacing the Black and Silver Release Sheet (Every 4–6 weeks)

  1. Remove and discard the Release Sheet.

  2. Lay a new Release Sheet on a clean, dry surface and fold it in half lengthwise and gently crease it at the fold using only your fingers.

3. Install the Release Sheet just as you would after Daily Cleaning. FOLD OVER SO ENDS MEET. PRESS LIGHTLY WITH FINGER TO FORM CREASE.

Belt Cover

Depending on toaster usage and how well they are cleaned daily, the Belt Wraps should last between 3–6 months.

  1. Turn unit off, unplug the power cord, and allow the unit to cool before proceeding.

  2. Remove the Bun Feeder and Heat Shield and set the Bun Thickness Compression Knobs to 6 & 6.

 

 

3. Open both Conveyor Covers and pull the Belt Wrap Pin out of the zipper.

 

4. Remove and discard the old Belt Wraps.

5. Clean both Conveyor Belt Chains just as you would clean the Belt Wraps during daily cleaning.

6. Install the new Belt Wraps around the Conveyor Belt Chains inside the yellow rods with the zipper flap exposed and hanging down.

7. Close the Conveyor Covers, set the Bun Thickness Compression Knobs back to their normal settings and reinstall the Heat Shield and Bun Feeder.

 

CHEMICALS & MATERIALS REQUIRED

  • All Purpose Cleaner

  • Quat Sanitizer

  • Cloth

ALWAYS:

  • Follow manufacturer’s recommendations for chemical use, dilution, handling, disposal and personal protective equipment (PPE).

NEVER:

  • Never use water hose or jet spray to clean unit.

  • Never use metal or abrasive objects to clean bun toaster (e.g. scrapers, scourers, steel wool) as this will cause damage to the heater plates and Teflon sheet.

SAFETY PRECAUTIONS:

  • Ensure power is turned off and cord unplugged before performing any maintenance or cleaning.

 

 

 

Related content